The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes. Be sure to unplug the washer before accessing internal components.

.

Keeping this in consideration, what does f1 mean on a Whirlpool Duet washer?

– Whirlpool Duet Washing Machine F1 error code indicates main control board and/or program faults. – Whirlpool Duet Washing Machine F2 error code indicates main control board and/or program faults.

Subsequently, question is, how do I reset my Whirlpool Duet washer? Unplug the washer for 30 seconds to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.

Also know, how do I fix f01 on my Whirlpool dryer?

The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse. The fuse is located on top of the blower wheel housing.

What does e01 and f09 mean on a washing machine?

Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.

Related Question Answers

How do you reset a front load washer?

How to reset the washing machine:
  1. Press POWER to turn the washer off.
  2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
  3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
  4. Plug the washer back in, or turn the circuit breaker back on.

How do you reset the code on a Whirlpool washer?

Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.

What does f01 mean on a washing machine?

electronic machine control board

Can you reset a Whirlpool washing machine?

How do I reset my Whirlpool washing machine? Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. The motor has now been reset and is ready for you to start a cycle.

How do I find the error code on my Whirlpool Duet washer?

Whirlpool Duet Alpha front-load washer error codes
  1. SUDS. Excessive suds. Check/
  2. F0 E1. Load detected during the washer cleaning cycle. Check/
  3. F1 E1. Main control board failure.
  4. F1 E2. Motor control board error.
  5. F2 E3. Main control board mismatch or main control board failure.
  6. F3 E1. Water level pressure switch failure.
  7. F3 E2. Temperature sensor failure.
  8. F4 E0. Water heater failure.

How do you get to the drain pump on a Whirlpool Duet washer?

The location of the drain pump filter in a Whirlpool Duet washer is accessible through the lower access panel below the washer door.
  1. Unplug your Whirlpool Duet washer power cord from the wall outlet.
  2. Find the screws securing the lower access panel to the washer cabinet.
  3. Remove the screws with a 1/4-inch nut driver.

What does it mean when a Whirlpool Dryer says f01?

The whirlpool Cabrio dryer F01 error means the main control has an internal failure. This can happen at any time when a component on the control board has failed but most commonly this happens when your home has a power surge and shorts the main control board.

How do you troubleshoot a Whirlpool Duet dryer?

How to Troubleshoot a Whirlpool Duet Electric Dryer
  1. Inspect household fuses or breakers.
  2. Close the dryer door firmly.
  3. Press and hold the "Start" button for five seconds.
  4. Check the display on the dryer for error codes.
  5. Press the "Start" button and hold for several seconds to restart the dryer if "PF" appears on the display.

What does f1 on my dryer mean?

The "F1" error means that the dryer's thermistor failed. The dryer is reading the thermistor as "open" and the actual part has shorted out. The thermistor is used to read and control temperatures within the dryer. Without the part, the dryer will not operate.

How long should a dryer last?

approximately 13 years

Where is the thermal fuse on a Whirlpool Duet dryer?

Remove the back access panel on the dryer, and look for the exhaust duct near the bottom of the unit. The thermal fuse is either circular or oblong, often white plastic with black material in the center and two wire leads. The thermal fuse is mounted on the exhaust duct.

How do you start a Whirlpool Duet dryer?

On the control panel of the Whirlpool Duet dryer, and similar dryers, you push both a "Power" button and an actual "Start" button to use the dryer. A cycle knob allows you to select your preferred drying cycle, but the "Start" button must be pressed to start the load of laundry.

What does Code F mean on Whirlpool Duet washer?

The F/dL code indicates a door lock error on the machine. When the door fails to lock to allow the cycle to begin, it attempts to lock itself at least six times before the error appears on the digital display screen. When the door fails to lock, the machine won't run at all.

Where is the filter on a Whirlpool Duet washer?

The filter on a Whirlpool Duet is located under the front kick plate. A washer filter collects lint that falls from clothes during the washing process. The lint filter should be cleaned at least once every 6 months. If the lint is not removed, it can cycle back through the washing machine and stick to laundry.

How do you unlock a front load washer?

How to Manually Unlock a Kenmore Front Load Washing Machine
  1. Touch "Control Lock" for five seconds until "CL" disappears from the washer's display to unlock the control panel.
  2. Press "Start/Pause" to manually pause the cleaning cycle.
  3. Pull the door's handle to open the door and add or remove the clothing from the washer.

How do you reset a washing machine?

How to reset the washing machine:
  1. Press POWER to turn the washer off.
  2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
  3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
  4. Plug the washer back in, or turn the circuit breaker back on.

How do I fix the code on my Whirlpool Duet washer?

LF in the display Check the water inlet hoses to be sure they are not clogged or kinked. You may also need to check the screens on the washer water inlet valve. This means shutting off the water supply, and disconnecting the water inlet hoses from the washer.

How long do washing machines last?

The average life expectancy of a new washing machine is 11 years. Consumer Reports recommends replacing any appliance that's more than eight years old, unless it's a high-end model and has a particular appeal to you. Others suggest replacing any top-loading washer manufactured in 1999 or earlier.

How do you unlock the door on a Whirlpool Duet washer?

Reach through the open panel and up to the door lock. Find the release ring below the locking mechanism. Pull down on the ring to unlock the door. If you must manually unlock the washer door after each wash cycle your drain pump or pressure switch may have failed and would need replacing.