1. Step 1: What You'll Need. Thankfully, not much you don't have already.
  2. Step 2: Prepare the Work Area.
  3. Step 3: Remove the Clutch Lever.
  4. Step 4: Slip on the Cable Luber.
  5. Step 5: Lube the Clutch Lever Cable.
  6. Step 6: Reinstall the Clutch Lever.
  7. Step 7: Disassemble the Throttle Cable Housing.
  8. Step 8: Lube the Throttle Cables.

.

Similarly, it is asked, can you use wd40 on throttle cables?

WD-40 is a lot thinner than cable lube/grease. It evaporates quickly and will likely not stay in the cable for long. If the cable was sticking due to corrosion/rust WD-40 would help break it free but I would not use it as a lube replacement. You should look into a non-aerosol cable lube.

Secondly, how do you fix a sticky throttle cable? With the throttle control lever in the “choke” position, pull on the outer jacket of the cable near the clamp until the choke plate opens. Tighten the clamp with the cable in this position. Reassemble the air cleaner. If your lawn mower's throttle cable is hard to move or stuck, here's a fix.

Just so, what can I use to lubricate motorcycle cables?

A mix of powdered graphite and WD-40 also works well for a lot of motorcycles or simply ask for a recommendation at your local motorcycle shop for getting the best lubricant for your particular motorcycle's cables. You should never use chain lubricant on a cable.

What is the best cable lube?

DuPont TriFlow and DuPont Silicone/Tefelon spray is very good for cable lube.

Related Question Answers

Can you use chain lube on cables?

The best chain lube is a wet lubricant, such as Chain L, Finish Line Wet, Pedros ChainJ, Ernesto Lube, or Bar and Chain Oil. An no, you should not use this on cables.

What kind of lube do you use on a clutch cable?

White Lithium Grease is a great, messy lubricant that likes to stay put. Perfect for hinges, window regulators and throttle, clutch and speedometer cables. If you use the little straw attachment you don't make much of a mess. Get some Cable Life with a little straw and this tool.

What is the best lubricant for motorcycle cables?

I would recommend that anyone using a motorcycle or bicycle with cable controls lubricate their cables with PJ1 Cable Lube. I've always sworn by PJ1 cable lube. It has great longevity, smells good, and the bubbling action really clears out dust/grit from cables as you pump it through with a cable-luber.

What is wire pulling lubricant?

Wire-pulling compound, also called cable lube or lubricant, is designed to make it easier to pull electrical wires and cables through conduit runs.

How do you clean a throttle cable?

Remove the fuel tank and seat so you can get to the carby. Release the end of the throttle cable from the carby so all the gunk doesn't get flushed into it when you clean out the cable. Attach a cable luber to the top end of the cable and spray contact cleaner into it to flush out the sand and dirt.

How do I know if my clutch cable is bad?

Symptoms of a Bad or Failing Clutch Cable
  1. Transmission slips out of gear. A bad clutch cable can sometimes cause a transmission to slip and pop out of gear.
  2. Hard clutch pedal. Another symptom of a problem with the clutch cable is a hard clutch pedal.
  3. Clutch pedal sinks to the floor.

What is Harley Lube?

Harley Lube is a Harley-Davidson® approved general lubrication oil that is perfect for lubricating clutch cables, Tour-Pak™ hinges, hand levers, footboards, footpegs, and windshield clamps.

Why does my throttle stick?

A sticky throttle could be caused by worn cables, lack of lubrication in the cables or the cable getting bound up somewhere in the mechanism. Or it can be caused by an issue with the carburetor or EFI. If the screws in the throttle housing are too tight it could cause the cable to stick.

Why does the throttle get stuck?

Most commonly, a stuck throttle results from debris getting caught between the throttle tube and handlebar that makes it sticky. Another common cause is when the throttle cable gets stuck in the open position and doesn't release when you let go of the throttle.

What causes your accelerator to stick?

If your accelerator were to stick it would most likely be caused by a floor mat or other object getting jammed under the gas pedal. This could obviously be avoided by keeping your vehicle clear of clutter and making sure floor mats are properly fixed in place.

What do I do if my throttle is stuck?

If your accelerator gets stuck down, do the following:
  1. Shift to neutral.
  2. Apply the brakes.
  3. Keep your eyes on the road and look for a way out.
  4. Warn other drivers by blinking and flashing your hazard lights.
  5. Try to drive the car safely off the road.
  6. Turn off the ignition when you no longer need to change direction.

How do you remove the throttle cable from a gas pedal?

  1. Step 1: Locate the throttle cable.
  2. Step 1: Disconnect the throttle cable at the throttle body.
  3. Step 2: Disconnect the throttle cable from the retaining bracket.
  4. Step 3: Pull the throttle cable through the firewall.
  5. Step 4: Disconnecting the throttle cable from the accelerator pedal.