most house's have either a 1"x2" covering the sheathing or molding, or it's wrapped in aluminum. We wouldn't reuse a drip edge, we would have removed it. If it bother's you have them remove it or replace it!

.

Likewise, do you have to replace drip edge when replacing roof?

Drip edge comes in 10-foot strips and attaches to the roof deck before the roofing felt goes on. Unless the old drip edge is in like-new condition, replace it.

Subsequently, question is, can Valley Metal be reused? However, valley lining cannot usually be reused. In the case of metal valley lining, the field shingles are nailed through it, so you are not likely to get your new shingles nailed through it again using the same nail holes.

Also to know, should drip edge match fascia or shingles?

Only the face of the metal is seen and is usually just white one to one and half inch stripe located right under the shingles and above the fascia. Most drip edge used to be installed as a 1” face in white color. The color is often chosen to match the shingles or the gutters to create a seamless look.

How do you replace drip edge?

Replacing Drip Edge Eave Strips:

  1. Install the eave strips on the lower roof edges first, with the eave strips under the shingles and felt underlayment.
  2. Align one end of the lower eave strip even with the edge of the roof decking.
  3. Lift up roof shingles, and nail the eave strip in place with galvanized roofing nails.
Related Question Answers

Do all roofs need a drip edge?

Often, the roofing drip edge isn't included in a bid if it's not a specific requirement. The reason for omitting it is usually to save money. Many roofers don't think the drip edge is needed, but this just isn't true. You actually do need a drip edge for your roof edges.

Do you install drip edge before tar paper?

The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.

How far should shingles overhang drip edge?

The edge of the shingles should hang over a roof between an inch and an inch and a half — or between a half inch and three-quarters of an inch if drip edge flashing is installed. Too much overhang and the shingles could blow off in high winds; too little can allow water to seep into rake or fascia boards.

Do roofers replace flashing?

Why don't roofing shingle manufacturer's recommend re-using roof flashing when replacing a roof? The short answer is, “because the nails don't always go back into the same holes they were in originally”. Practically, however, when you're replacing a 15-20 year old roof, you don't know: 1.

Do you overlap drip edge?

Nail high up on the drip edge so that the shingles will cover the nails. Ideally, you'd nail about every 12 inches, and in no circumstances should you have 16 inches or more between nails. When you place the next drip edge piece, it should overlap the first by an inch.

What is the purpose of a drip edge on a roof?

Drip edge is a metal flashing that is installed at the edges of the roof to help control the flow of water away from the fascia and to protect the underlying roofing components. Drip edge overhangs the sides of the roof and has a small metal flange that is bent away from the fascia.

Do you install gutters under drip edge?

A permanent solution you should consider is installing drip edge. Drip edge gets installed under the first course of shingles and promotes water to run freely from roof edge down into gutter. Without it, water may run down behind your gutter, down fascia board and siding, leading to potential damage.

Why do my gutters drip?

If the gutters are clogged, it's possible that the water is overflowing the gutters and this is contributing to the leak. Water should run out the downspout and away from the house without filling the gutter. If the water fills the inside of the gutter, this means the gutters are clogged.

Should drip edge be painted?

Painting your drip edge does two chief things. First and foremost, when you paint and prime a drip edge, it's going to seal the drip edge itself against moisture damage. The primer will lay down a sealant foundation, while a water-resistant, exterior-approved paint will complement it, creating a waterproof barrier.

Is drip edge needed with metal roofing?

Drip edge is a metal flashing that is installed at the edges of the roof to help control the flow of water away from the fascia and to protect the underlying roofing components. It is non-corrosive and non-staining so that your roof looks good but is structurally stable.

How do you replace fascia with drip edge?

Pry up with a cat's paw or nail puller the nails in the drip edge's bottom flange where it meets the fascia board. Pull the drip edge's top flange out from under the shingles and carefully set it aside for potential reuse.

Should you use drip edge touch fascia?

The drip edge should be installed over a piece of 1×2 furring strip so that it stands off from the fascia or rafter tails. If the drip edge is laid right up against the fascia or rafters, then because of surface tension, the water runs right up against the fascia and underneath the soffit.

Does drip edge go on rakes?

Drip edge goes along your eaves trough areas and rake edge goes along your gable ends. They both look very similar and are often not differentiated in name by some suppliers and simply called drip edge.